Info
Honest John
Alle Bewertungen (2.168)
- katernetr (29852)- Bewertung vom Käufer.Letzter MonatBestätigter KaufGreat communication. A pleasure to do business with.
- eorder0612 (12870)- Bewertung vom Käufer.Letztes JahrBestätigter KaufHope to deal with you again. Thank you.
- *****- Bewertung vom Käufer.Letztes JahrBestätigter KaufFinedon Electronics - Thankyou for your Purchase A++++
- luckyseller-11 (12580)- Bewertung vom Käufer.Vor über einem JahrBestätigter KaufGreat communication. A pleasure to do business with.
- instantdeal (72)- Bewertung vom Käufer.Vor über einem JahrBestätigter KaufGood buyer, prompt payment, valued customer, highly recommended.
- nav120admin (19391)- Bewertung vom Käufer.Vor über einem JahrBestätigter Kauf★★★★★Thank you buying from Electronic123★★★★★
Rezensionen (19)
27. Mai 2017
Casters
My wife's laptop table had these, but with smaller bolts, these are much stronger.
They are well made, but a bit disappointed they didn't come with fixing nuts
07. Okt 2019
Not a bad system, more expensive ones wont do any better
I installed this in an Epson XP 760, since this suppose to do other models you might/will have parts not needed. The photos supplied were terrible, totally no good at all, I had to view several youtube videos before attempting. It shows a "Roller" in the photos supplied, but i didn't get one, think it suppose to stop ink coming out. So this is what I did on my 760 printer.
Placed the cartridge set in, put the orange bottoms on old cartridges, never throw those orange covers away, hard to get.
1, orange base removed on all cartridges, put them all in printer
2, removed both plugs on ink bottles
3, placed air filter into small holes on bottles
4, filled up a bottle one at a time
5, fill Light Magenta bottle up full
6, remove small bung on light magenta cartridge
7, insert syringe into light magenta hole (no needle) and suck slowly
8, remove syringe close it, then suck again
9, keep sucking until ink comes into syringe, then slowly remove syringe and fit bung quickly
10, any ink sucked out squirt back into bottle
11, fit large bung back onto bottle
now do the same with other colours
You need to tell the printer to change cartridge, when its stops, push the heads over to left all the way. On the 760 there is a tube holder that plugs into a hole, that hole has a microswitch telling the printer you closed the lid, so this plastic keeps the switch on all the time, telling printer lid is closed. Now just fit tube into it (see photo) and make sure its loose, push heads over to right and left to make sure tubes dont snag on anything.
Finally fit a clamp down the side of the printer for the vertical tube.
You will need to tell the printer to clean heads, it too 3 cleans and 3 test pages before it was perfect, just like fitting a new cartridge you suppose to wait a few hours before use.
Note, printer lid stays open, all kits do this, else tubes would be squashed, should not effect scanner at all...
27. Mai 2017
The all new BaoFeng UV-5RTP
Great radio, and works 100% with chip program. plug the lead in, windows 10 may install a new driver, if not use the disk, then windows 10 may update that driver.
Then all you need to do is select it in your Control Panel Device Manger, select the one with the yellow warning mark select update driver Browse my computer Let me pick then from the list of drivers, pick an old driver, perhaps 2010, make a note of com port.
The radio really works well, high 8W of power gets you out, works great on radio ham bands and PMR, really good value for money