Info
Alle Bewertungen (1.307)
netleymarsh (1552)- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
great buyer glad your happy with the chuck
fonejacketltd (14352)- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
Thankyou for Shopping at FONEJACKET for Phone Accessories at the best prices
fonejacketltd (14352)- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
Thankyou for Shopping at FONEJACKET for Phone Accessories at the best prices
*****- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
--
exclusive_arts (51495)- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
Thank you for your purchase your custom is greatly appreciated
kenable_ltd (2215394)- Bewertung vom Käufer.
Letzter Monat
Bestätigter Kauf
Thanks for your purchase from the kenable team
Rezensionen (42)
20. Sep 2017
Quality lock
I bought 2 of these great little locks to fit on two cupboards that i built, once they arrived i was impressed with the smoothness in which they open & closed, their very well made & well finished off, when fitted all you see is the key hole & the trim on the front. I have just one small comment to make & that would be a papper or card template would make it easier to fit, but thats no hardship, would deffinatley recomend to any one looking for a quality little lock. Keith
28. Jul 2016
well made key safe
This key safe is well made, very good value, & looks good on the wall, would recommend it to any one, good, strong & nice looking when mounted on wall. Keith NI
21. Dez 2019
This 50amp plasma cutter is a great machine
4 von 5 finden das hilfreich I ordered up this 50amp plasma cutter & it was soon delivered,
I opened up the box a found it to be well packed, on removing the contents of the box, there was a good supply of consumables, cutting torch, earth clamp, air regulator & the fittings to connect it up including the worm drive clips, instruction & spare parts book,
I started building up the air regulator, firstly fitting the mounting bracket below the large nut on top of regulator & tightened it up, then added some PTFE tape to one of the brass male fittings & screwed the male fitting into the out side of the regulator, then added PTFE tape to my male quick release fitting & screwed that in to the inlet side of regular & tightened up, then added PTFE tape to pressure gauge & fitted to regulator then fitted complete unit to plasma machine on left hand side (when viewed from front) on the 2 screws provided, this is where I would have a criticism, you have to supply approximately 300mm (12") of air line hose to connect from the air outlet on regulator to the air inlet on the back of machine, (reference picture 1)
I then connected up the air line, plugged into 16amp supply & turned on the plasma cutter, set air pressure on regulator to 50 psi & set the amps to 15, put on my auto darkening welding shield & started to cut a piece of 3mm m/steel plate, found I needed more air turned up to 65psi & away I went, not the cleanest of cuts, but not bad for first time,
I decided to up the plate thickness to 8mm & set amps at 30 & up the air pressure to 70psi, away I went through the 8mm plate, nice clean cut & quite smooth finish very pleasing, tried cutting 12mm plate at 35amp same pressure, even better than the 8mm plate, very impressed so far, I then tried 16mm plate at 40amps & same pressure 70psi with good results, almost cut completely through, I think with a little fine tuning it would definitely cut 16mm mild steel plate,
This is a impressive machine, & I would definitely recommend this 50amp plasma cutter to any one looking one, it is very good value for money & a very well made & finished machine,
photo 2, the cut on 12mm plate, Keith NI