Bewertungen und Rezensionen

Mehr erfahren

4.7

79 Produktbewertungen

59 Nutzer haben dieses Produkt mit 5 von 5 Sternen bewertet
16 Nutzer haben dieses Produkt mit 4 von 5 Sternen bewertet
3 Nutzer haben dieses Produkt mit 3 von 5 Sternen bewertet
0 Nutzer haben dieses Produkt mit 2 von 5 Sternen bewertet
1 Nutzer haben dieses Produkt mit 1 von 5 Sternen bewertet

Good value

Would recommend

Good quality

Relevanteste Rezensionen

Alle 75 Rezensionen sehen

von westcosunrise
15. Dez. 2020
It operates just fine as intended
I installed this on my Campbell Hausfeld compressor from the 80's, If fit just fine and works as intended. Only time will tell how long it will last in operation, The cut-in and cut-out pressures were easy to adjust. While the original part was housed in metal this unit has a plastic cover. One thing that was not expected was that this unit has a female pipe thread for hookup as seen in the auction pictures and I needed to go to the hardware store to get a small threaded male coupling pipe. I could have used "close" but opted for 1".so the unit stands off the compressor port a little, which made the installation a tad easier. I did not take my compressor switch off prior to obtaining this switch unit so that was my error.
Bestätigter Kauf: JaArtikelzustand: Neu
von techy_one-0-one
20. Jul. 2021
Suitable replacement pressure switch that required minor modifications
Appears to be well built. Used it to replace my failed pressure switch on a small shop air compressor. I was able to use the existing head pressure release hose by removing coupling nut and compression sleeve then using nut included with pressure switch with the original compression ring. The fit was not perfect and lightly leaks but only when compressor runs, so it doesn't affect the overall operation. I did have to slightly bend the little arm that operates the release valve as it did not contact the tip of the release valve to dump the head pressure when machine shut off but it works flawlessly now. The major drawback to using this switch was the fact that there is only one pressure port and the original had multiple ports. I had to get a 4-way plumbing tee, a standard tee and several short pipe nipples to add the over pressure safety valve, the new pressure switch, the tank, the pressure gauge, and output regulator together. The air compressor operates as well as it ever did now and saved me a fair amount of money over replacing the entire unit. I am very happy with the results even with the additional work required.
Bestätigter Kauf: JaArtikelzustand: Neu
von rocketman53
22. Dez. 2020
New on-off switch for my 35 year old Speedair compressor
This is a replacement on-off compressor switch for my Speedair air compressor. The Furnas brand original switch on my 35 year old compressor wore out the contacts in the on-off switch and I had to replace it. I looked on line and the reviews for this switch were OK, and it was much less expensive than a new Furnas or Square D switch, so I am giving this one a try to see just how long it will last. For the price, I can replace several of them for one of the original ones. It will just be a hassle switching them out should this switch not last too long. It would be much more convenient to be able to buy just the replacement contacts for the original switch, but I could not find a set of replacement contacts, and I had to buy the complete switch. I know how to remove the contact block and hold the spring loaded unloader valve in place to reassemble it, so it would not be a problem to just replace the contacts if I could find them. With the throw-away thinking of today's mentality, the switch companies want you to have to buy a complete switch, not just replacement contacts. Only time will tell if it will last. Stay tuned on that issue.
Bestätigter Kauf: JaArtikelzustand: Neu
von al_wengerd
17. Aug. 2019
Good product and good value!
I put this pressure switch on an older Sears air compressor. It was easy to install and works perfectly. The compressor comes on and shuts off exactly where it's supposed to. The pressure is easily adjustable with instructions under the cover if needed. I would buy it again and recommend it to anyone.
Bestätigter Kauf: JaArtikelzustand: Neu
von mikbohme-0
11. Nov. 2020
all fit just leaks can't use leaks over night and comes on over night about 4 times don't want ta burn out my motor .
Turns off and on but go's up ta 135 pounds turns off but leaks at the 1/4" press valve replaced the line and still leaks at the bottom un plugged it .
Bestätigter Kauf: JaArtikelzustand: Neu
von roscoguy
24. Jan. 2025
This switch is well made & an almost per...
This switch is well made & an almost perfect replacement for the original one for my air compressor. "Almost" because I'm not crazy about the rubber grommets this one has instead of a better cord lock.
Bestätigter Kauf: JaArtikelzustand: Neu
von ajc2002
01. Jun. 2020
Almost perfect lol
I said almost perfect because of a tiny flaw.(the original pressure switch had a male threaded end) I happen to have the 1/4 threaded nipple lying around so I was able to get my older sears compressor up and running within 15 minutes. Every other part, electrical and air fitting lined up perfectly. I would buy it again. Its so nice to have the thing starting and stopping like it used to. GREAT VALUE AND PRICE
Bestätigter Kauf: JaArtikelzustand: Neu
von russellarabe-0
04. Mär. 2020
Well made- Does the job
It was oriented differently than the original unit, which was no longer available, but was easy to install and serves the purpose very well
Bestätigter Kauf: JaArtikelzustand: Neu
von tnunes4swo
17. Aug. 2021
Just needed a part
I just needed the unloader valve for my Furnas pressure switch. This was an exact copy so I removed the unloader valve and put it on my Furnas pressure switch. That was faster and easier than changing the complete switch. It works perfectly and now I have the rest of the pressure switch in case the Furnas switch fails in the future. The compressor is an Ingersol Rand T10 built in 1992. This pressure switch is an exact copy of the original Furnas switch. The quality of this Chinese import appears to be good. I don’t know how it would hold up but at the price it is worth the gamble.
Bestätigter Kauf: JaArtikelzustand: Neu
von antho_9175
26. Mär. 2022
High quality product, fair price.
For a few dollars I was able to bring my 40+ year old compressor back to life. Easy to install, fast shipping.
Bestätigter Kauf: JaArtikelzustand: Neu