Aktuelle Folie {CURRENT_SLIDE} von {TOTAL_SLIDES}- Meistverkauft in Rasenmäher-Ersatzteile
Aktuelle Folie {CURRENT_SLIDE} von {TOTAL_SLIDES}- Hier sparen: Rasenmäher-Ersatzteile
Aktuelle Folie {CURRENT_SLIDE} von {TOTAL_SLIDES}- Auch interessant
Arrived on time and well packaged. After reading the supplied instructions, I fitted the sharpener to the mower very quickly. I adjusted the cylinder blades, so they just touched the sandpaper. I started the mower a set the tick-over to a slow speed for a few minutes, then stopped the mower and checked the blades. I gradually adjusted the cylinder and started the mower for a few minutes, then checked the blades until all the cutting edge was shiny along it's length. When finished, I reset the cylinder blades to the correct setting. This took a total of 20 minutes, which I thought was not bad for the 1st time.
Bestätigter Kauf: Ja | Artikelzustand: Neu
Don't over tighten the attachment screws as they are just plastic. Just enough to hold the bar securely. Don't try to take too much off in one pass. Adjust the blade gradually. I took about 30 mins to get to a decent sharpness with an even cut across the width.
Bestätigter Kauf: Ja | Artikelzustand: Neu
Firstly this was quite difficult to fit in the right position, but after a while I managed it. However, the screw fittings are made of cheap plastic and one of them broke when I attempted to push the mower as instructed, and the sharpener fell off. I tried using it by placing the mower on its side instead, and turning the wheels by hand, but this did not seem to have any effect on the sharpness of the blades. In the end I used one of those cheap hand-held knife sharpeners which cost about £2, sharpening each blade of the cylinder by hand. This worked reasonably well and seems to have improved the cutting capability. Overall I am disappointed with this product, it is cheaply made (metal fittings would be better and would not cost much more) and it does not work particularly well, and is very expensive for what it is , ie, a bit of plastic and metal with some sandpaper stuck on it. I suspect this high price is charged because people see it as a cheaper alternative to professional sharpening (I was quoted £30, which is half the cost of the mower itself). But if you want to save money I would suggest using one of those cheap knife-sharpeners first.Vollständige Rezension lesen
Bestätigter Kauf: Ja | Artikelzustand: Neu
Simple idea, easy to use & perfect results. Follow the easy to understand instructions & the blade is as good as new. Used on my 30 year old Qualcast 30S Punch & saved paying £55 for a regrind. Only used one abrasive too.
Bestätigter Kauf: Ja | Artikelzustand: Neu
easy to fit to cylinder mower and sharpens well, good instructions. can be used more than once to keep blades in good order
Bestätigter Kauf: Ja | Artikelzustand: Neu
The plate fitted ok but the sharpening strips would not stick on because the backing was completely dry so much that the backing paper just fell off when I unpacked it so I had three useless sharpening strips .havent got time for all the hassle of trying to send it all back as I had cut open the blister pack etc .
Bestätigter Kauf: Ja | Artikelzustand: Neu
Excellent little blade sharpener, bought for a project refurb mower, fitted straight away and began to sharpen mower cylinder blades. Took little adjustment, excellent product. Arrived sooner than stated, even better. Would totally recommend, not expensive but is a quality built product.
Bestätigter Kauf: Ja | Artikelzustand: Neu
Very good idea, the only downside is it seems very pricey for a small length of aluminium extrusion.
Bestätigter Kauf: Ja | Artikelzustand: Neu
Not worth the money and very difficult to put on a manual hand push lawn mower, the instruction is useless. If you have a manual hand push lawn mower best thing to do is get a file and sharpen it by hand.
Bestätigter Kauf: Ja | Artikelzustand: Neu
Did a good job, better finish than grinding, excellent delivery
Bestätigter Kauf: Ja | Artikelzustand: Neu
